Perle eX-1S1110-BNC-XT
Gigabit Industrial Temperature Ethernet Extender - 1 port 10/100/1000Base-T (RJ-45). BNC ( Coax ) Interlink ( VDSL2 ) connector
Catalogusprijs:
€ 836,00*
Dealer prijs - Aanmelden
Levertijd: Momenteel ongeveer 3-4 weken
Prijzen voor grotere hoeveelheden op aanvraag.
Phone: +31 (0) 6 512 97 427 or e-mail: shop@s-connect-benelux.com
Phone: +31 (0) 6 512 97 427 or e-mail: shop@s-connect-benelux.com
Artikelnummer van de fabrikant:
06003660
Ons artikelnummer:
221509
Vragen? Wij adviseren u graag! → Contactformulier
Productinformatie "Perle eX-1S1110-BNC-XT"
When you need to extend Ethernet services beyond the general IEEE 802.3 limits of 328ft / 100m in extreme temperatures, and new fiber cabling is cost prohibitive, Ethernet Extenders are the perfect solution. Perle Ethernet Extenders transparently extend up to four 10/100/1000 Ethernet connections across copper wiring. Use single twisted pair ( CAT5/6/7 ) or any existing copper wiring previously used in alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV applications.
Equipment found in traffic management, oil and gas pipelines, weather tracking, industrial and outdoor applications must function in temperatures that cannot be supported by a commercial based Ethernet Extender. With the ability to operate in industrial grade temperatures of -40°F to +167°F (-40°C to +75°C) along with a rugged steel casing, these simple and effective point to point Ethernet Copper Extenders are ideal to extend the distance between two industrial Ethernet devices subjected to harsh environments and severe temperatures such as security cameras, wireless access points, alarms, traffic controllers, sensors and tracking devices.
Perle’s advanced features such as Link Pass-Through*, Interlink Fault Feedback*, and Loopback allow Network administrators to “see everything” for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle Ethernet Extenders the smart choice for IT professionals. eX-S1110 Ethernet Extenders are also available with support for Commercial Temperature ranges, managed networks with AAA security and high density applications.
Scope of delivery: Perle Systems - eX-1S1110-BNC-XT
Equipment found in traffic management, oil and gas pipelines, weather tracking, industrial and outdoor applications must function in temperatures that cannot be supported by a commercial based Ethernet Extender. With the ability to operate in industrial grade temperatures of -40°F to +167°F (-40°C to +75°C) along with a rugged steel casing, these simple and effective point to point Ethernet Copper Extenders are ideal to extend the distance between two industrial Ethernet devices subjected to harsh environments and severe temperatures such as security cameras, wireless access points, alarms, traffic controllers, sensors and tracking devices.
Perle’s advanced features such as Link Pass-Through*, Interlink Fault Feedback*, and Loopback allow Network administrators to “see everything” for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle Ethernet Extenders the smart choice for IT professionals. eX-S1110 Ethernet Extenders are also available with support for Commercial Temperature ranges, managed networks with AAA security and high density applications.
Scope of delivery: Perle Systems - eX-1S1110-BNC-XT
| Connection: | 10 / 100 / 1000, Gigabit |
|---|---|
| Mounting: | DIN-Rail, Rackmount |
| Temperature Range: | -40°C to 75°C |
Features
- Extends 10/100/1000Base-T Ethernet up to 10,000 feet ( 3 KM ) over 2-wire 24 AWG twisted pair
- Rugged-designed for harsh industrial -40°C to 75°C temperatures ( -40°F to 167°F )
- High-Speed – up to 200+ mbps aggregate line rate
- Transparent operation for all Ethernet protocols including 802.1Q VLAN packets and IP video compression schemes
- One or four 10/100/1000 Ethernet ports
- Advanced features: Link Pass-Through*, Interlink Fault Feedback*, Auto-MDIX and Loopback
Technical details
Ethernet
Port: 1 port RJ45 – 10/100/1000Base-T - Shielded
Auto-MDIX: Auto-MDIX enables proper operation with either straight-through or crossover cabling
Distance: Distance up to 100 meters (328 feet) as per IEEE 802.3
Maximum Frame Size: 1522 bytes
VDSL – Interlink
RJ45, BNC, Terminal Block: Ethernet Extenders must be connected in pairs using unconditioned wire. Circuits that run through signal equalization equipment are not permitted. TIP and RING are polarity insensitive. Surge suppression of 400 volts between TIP and RING. Choice of RJ45, BNC or terminal block models for VDSL link connector:
Power
Input Supply Voltage: 9 - 30 vDC, unregulated (12 vDC Nominal)
Current: 350 mA
Power Consumption: 4.2 watts
Power Connectors: 5.5mm x 9.5mm x 2.1mm barrel socket and 2 pin terminal Block
Power Adapter
Universal AC/DC adapter: Optional Industrial Temperature 100-240v AC, regulated 12V DC adapter
Indicators
Power / TST: This green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.
CO - Local: Ethernet Extender is operating in CO VDSL mode
CPE - remote: Ethernet Extender is operating in CPE VDSL mode
ILNK: Indicates Link Status and activity on the Interlink (VDSL) port
ETH: Indicates link status and activity on Ethernet port(s)
Switches
Access: All switch settings are accessible through a side opening in the chassis
Rate/Reach: Two switches enable the user to select the right balance between speed and distance for their environment.
Signal to Noise Ratio: Selectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.
Auto-Negotiation (802.3u): Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex. Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.
Link Mode: Standard (Default) – The 10/100/1000Base-T link remains active independent of the state of the Ethernet link on its remote peer.
Link Pass-Through- the state of the 10/100/1000Base-T Ethernet connection is “passed through” or propagated across the VDSL link to the 10/100/1000Base-T Ethernet link on its remote Ethernet Extender peer. This enables a managed switch to report the state of the remote device to its network management system.
Interlink Fault Feedback: Enabled - A loss of VDSL link will drop the 10/100/1000 Ethernet port on each end until the link recovers. Disabled (Default) – The state of the VDSL link is not propagated to the 10/100/1000Base-T port
Loopback: Enabled - The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its peer. Disabled (Default - Up)
Set Ethernet Speed (Port 1): When Auto-Negotiation switch is disabled, fixed speed can be set at 1000 (Default) or 100 or 10
Set Ethernet Duplex (Port 1): When Auto-Negotiation switch is disabled, Duplex can be set at Full (Default) or Half
Environmental Specifications
Operating Temperature: -40°C to 75°C (-40°F to 167°F)
Storage Temperature: minimum range of -40°C to 85°C (-40°F to 185°F)
Operating Humidity: 5% to 90% non-condensing
Storage Humidity: 5% to 95% non-condensing
Operating Altitude: Up to 3,048 meters (10,000 feet)
Heat Output (BTU/HR): 14.3
MTBF (Hours): 466,861
Mounting
Din Rail Kit: Optional
Rack Mount Kit: Optional
Product Weight and Dimensions
Weight: 0.33 kg, 0.73 lbs
Dimensions: 120 x 80 x 35 mm, 4.7 x 3.1 x 1.4 inches
Ethernet
Port: 1 port RJ45 – 10/100/1000Base-T - Shielded
Auto-MDIX: Auto-MDIX enables proper operation with either straight-through or crossover cabling
Distance: Distance up to 100 meters (328 feet) as per IEEE 802.3
Maximum Frame Size: 1522 bytes
VDSL – Interlink
RJ45, BNC, Terminal Block: Ethernet Extenders must be connected in pairs using unconditioned wire. Circuits that run through signal equalization equipment are not permitted. TIP and RING are polarity insensitive. Surge suppression of 400 volts between TIP and RING. Choice of RJ45, BNC or terminal block models for VDSL link connector:
- RJ45 – RING pin 4, TIP pin 5 (TIA 568 A/B)
- BNC – Coaxial 50 and 75 ohm cable with BNC connector
- Terminal Block – 2 position screw connectors for use with twisted pair telephone, alarm or serial cabling between 19 (0.9 mm) and 26 AWG (0.44 mm)
| High Speed Asymmetric | |||
|---|---|---|---|
| Reach (Distance) | VDSL Rate (Mbps) | ||
| feet | meters | Downstream | Upstream |
| 500 | 152 | 101 | 92 |
| 1000 | 305 | 101 | 63 |
| 1500 | 457 | 90 | 38 |
| 2000 | 610 | 62 | 24 |
| 2500 | 762 | 55 | 10 |
| 3000 | 914 | 42 | 5 |
| 3500 | 1000 | 35 | 3 |
| High Speed Symmetric | |||
|---|---|---|---|
| Reach (Distance) | VDSL Rate (Mbps) | ||
| feet | meters | Downstream | Upstream |
| 500 | 152 | 101 | 101 |
| 1000 | 305 | 85 | 101 |
| 1500 | 457 | 62 | 47 |
| 2000 | 610 | 60 | 29 |
| 2500 | 762 | 44 | 14 |
| 3000 | 914 | 30 | 7 |
| 3500 | 1000 | 29 | 4 |
| Long Reach Symmetric | |||
|---|---|---|---|
| Reach (Distance) | VDSL Rate (Mbps) | ||
| feet | meters | Downstream | Upstream |
| 500 | 152 | 53 | 44 |
| 1000 | 305 | 53 | 43 |
| 2500 | 762 | 39 | 18 |
| 4000 | 1219 | 25 | 4 |
| 5500 | 1676 | 17 | 1.9 |
| 7000 | 2134 | 8 | 2.3 |
| 7500 | 2286 | 7 | 2.2 |
| 8000 | 2438 | 5 | 2.2 |
| Long Reach Asymmetric | |||
|---|---|---|---|
| Reach (Distance) | VDSL Rate (Mbps) | ||
| feet | meters | Downstream | Upstream |
| 500 | 152 | 78 | 16 |
| 1000 | 305 | 78 | 16 |
| 2500 | 762 | 55 | 10 |
| 4000 | 1219 | 31 | 0.8 |
| 5500 | 1676 | 20 | 0.6 |
| 7000 | 2134 | 11 | 0.6 |
| 7500 | 2286 | 10 | 0.6 |
| 8000 | 2438 | 8 | 0.6 |
Power
Input Supply Voltage: 9 - 30 vDC, unregulated (12 vDC Nominal)
Current: 350 mA
Power Consumption: 4.2 watts
Power Connectors: 5.5mm x 9.5mm x 2.1mm barrel socket and 2 pin terminal Block
Power Adapter
Universal AC/DC adapter: Optional Industrial Temperature 100-240v AC, regulated 12V DC adapter
Indicators
Power / TST: This green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.
CO - Local: Ethernet Extender is operating in CO VDSL mode
CPE - remote: Ethernet Extender is operating in CPE VDSL mode
ILNK: Indicates Link Status and activity on the Interlink (VDSL) port
ETH: Indicates link status and activity on Ethernet port(s)
Switches
Access: All switch settings are accessible through a side opening in the chassis
Rate/Reach: Two switches enable the user to select the right balance between speed and distance for their environment.
Signal to Noise Ratio: Selectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.
Auto-Negotiation (802.3u): Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex. Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.
Link Mode: Standard (Default) – The 10/100/1000Base-T link remains active independent of the state of the Ethernet link on its remote peer.
Link Pass-Through- the state of the 10/100/1000Base-T Ethernet connection is “passed through” or propagated across the VDSL link to the 10/100/1000Base-T Ethernet link on its remote Ethernet Extender peer. This enables a managed switch to report the state of the remote device to its network management system.
Interlink Fault Feedback: Enabled - A loss of VDSL link will drop the 10/100/1000 Ethernet port on each end until the link recovers. Disabled (Default) – The state of the VDSL link is not propagated to the 10/100/1000Base-T port
Loopback: Enabled - The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its peer. Disabled (Default - Up)
Set Ethernet Speed (Port 1): When Auto-Negotiation switch is disabled, fixed speed can be set at 1000 (Default) or 100 or 10
Set Ethernet Duplex (Port 1): When Auto-Negotiation switch is disabled, Duplex can be set at Full (Default) or Half
Environmental Specifications
Operating Temperature: -40°C to 75°C (-40°F to 167°F)
Storage Temperature: minimum range of -40°C to 85°C (-40°F to 185°F)
Operating Humidity: 5% to 90% non-condensing
Storage Humidity: 5% to 95% non-condensing
Operating Altitude: Up to 3,048 meters (10,000 feet)
Heat Output (BTU/HR): 14.3
MTBF (Hours): 466,861
Mounting
Din Rail Kit: Optional
Rack Mount Kit: Optional
Product Weight and Dimensions
Weight: 0.33 kg, 0.73 lbs
Dimensions: 120 x 80 x 35 mm, 4.7 x 3.1 x 1.4 inches